Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hi,
Does Nordic Semiconductor provide any resources (codes, macros, documents) for work with IAR or Keil's simulator to fully simulate nRF51822's peripherals?
Thanks...
Hi,
I do:
err_code = ble_bondmngr_bonded_centrals_delete();
APP_ERROR_CHECK(err_code);
till now all is ok.
But when I do:
err_code = ble_bondmngr_whitelist_get...
Hi,
I need to delete all centrals using ble_bondmngr_bonded_centrals_delete ble_bondmngr.c function. It is working but it is not cleaning the whitelist.
So, when I do...
In the example of hid_mouse, ble device will bond master when disconnect event happen.
I try to add this two codes to Implement my idea.
err_code = ble_bondmngr_bonded_masters_store...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
Hello:
I am using NRF51822 to design somethings. And I want to use interrupt send method instead of polling send method.
NRF51822's UART0 provides TXDRDY interrupt. After...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
Hi,
I am trying to set a value in the NRF_POWER->GPREGRET when softdevice is running, but it doesn't work. I don't get any error, but the value is always 3 and not 1 like...
