Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
/**
* @brief Function for unconfiguring GPIOTE channel.
*
*
* Note that when unconfiguring the channel, the pin is configured as GPIO PIN_CNF configuration.
*
...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I have set up the UART example with PCA10000 and PCA10001. Everything works fine but one strange thing is the time to send 100kB of data. See my times below:
38...
Hi !
On this thread devzone.nordicsemi.com/.../nrf51922-1 i've found someone introducing the new S130 softdevice for the nRF51822 wich allows the IC to be on concurrent...
Hi to all,
Ihave a problem with erasing flash on nRF51422 Evaluation Kit. When i click on Erase all button in nRFGo Studio everything is looking normal ( segger led is blinking...
I cannot download S110 to try right now. I have some 51822 Dev kits, but somehow I didn't get the product keys entered into my page, and the boxes are all gone.:D
When my application is running on the nRF51822 (e.g. the hrs example from the sdk), I want to stop this application (e.g. at a breakpoint), investigate some memory and than...
Hi,
I've started developing some test applications for the nRF8001 to better understand all the ACI libraries and improve my knowledge of the chip.
I'm experiencing some...
Unless manually set the value of bond_init_data.bonds_delete to true in the function bond_manager_init to clear bonded masters, I end up in the HardFault_handler. The last...
I'm trying to just set up a Timer for 8 MHz frequency and have that output on a pin. It seems simple but I'm having some problems (the frequency is a lot lower). What am I...
Hi everyone,
I've just started to develop software for NRF51822 - Bluetooth Low Energy on the Evaluation Kit. I managed to connect the development dongle and evaluation...
Based s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK v. 4.4.1
When scanning iOS, why not click pair on the iOS side and NRF51822
connected on? whether the pair can be...
Hi,
I'm planning a hardware solution and I need a BLE IC capable of act as a master and a slave, not at the same time, but with the possibility to change it's role by software...
I used nrf8001 to implement ANCS.It working fine.But when it disconnect for a while and reconnect(reconnect successed).I found Iphone can't send any ANCS message to nrf8001...
