Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
We are using nRF51822 evaluation kit. Actually we are trying to know how the device firmware upgrade is working.
As mentioned in the nrf51 sdk manual, we did flashing...
Hi,
i need to store data in my Flash, for that i use the flashwrite example. Am i right taht i can use the remain of my application flash? So all flash = 256 kB - App ...
Hello everybody
it's a couple of mounth that our company is working on nrf24L01P .It works fine but there is a problem with cordless phone.
when I make a call with the a...
Hi
Is timer ,gpio ,and spi pheripherals are accessible while bluetooth stack is enabled.
and if it is yes , these are directly accessible or we need to use soft device...
But in button event handler.
i want data to read from eeprom through i2c bus. and send it
through bluetooth stack for every press of buuton 0.
but in master control...
Hi,
Is it possible to start a Timer in an other Timeouht Handler?
Or Do i have to use something other to do that?
i use app_timer and Softdeive on the 51822.
best...
Hi,
i need to add a logfile System to my application so i thogut i could use the nrfUart example is this possible ? I looked in the code of Master Emulator nrfUart in C#...
Hi 'Nordic' guys,
splitting the original S110 hex file provided by Nordic , version 5.2, there is an error extracting uicr section.
Now is only 20 bytes and not 32 as...
Hi,
Is it possible to wakeup nrf51822 without using the GPIO peripheral's (i.e configuring a gpio button as a sense enabled)?
how to do soft reset?
Actually my requirement...
Hi,
i need to make pulse with one of my Timers. Timer0 is used by the softdevice, and Timer2 is used to make PWM. I need to make a Pulse wich is 100us long, every 250ms...
Hi,
What is the procedure and source code required to enable Device Firmware Update over BLE and USB. We are using nRF51822 chipset. Assume that our requirement will be...
Hello,
I am using a nRF51822 DK.
Actually I want to develpoe a product what can connect 3~10 slave(Low Battery device) by BLE.
And they have to reconnect fastly anytime...
A friend installed on two XP machines this software in this order..
Keil's mdk472.exe
Nordic's nrfgo_sdk_2.3.0_setup.exe
Nordic's nrfgostudio_installer_1_14_1...
I downloaded the nRF51SDK and followed the Quick Start guide in the Evaluation Kit Userguide (KEIL, Segger, etc)
But when I install nRF51 SDK v4.3, the installation failed...