Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi
I am coding a s130 NUS example.
The base example is sdk8.1.0 ble_app_uart peripheral example.
I added central part from Github sdk8.0.0 ble_app_uart_c...
Hi
I've installed the new tools in version 7.5.1 to support the new nRF52 family. While working on the nRF51 again i found out, that the old parameters i used for programming...
Hi,
I'm working on a project where nrf51 modules should communicate with each other. For that i'd need to set characteristic that can store string. Now i've done that ...
Hi,all.i call function "sd_clock_hfclk_release(); power_manage();" and want my device to sleep.as this,my device's current is 2.2mA.what's wrong ?Can someone help me?
I have a master device using SPI interface , write data to nordic SPI salve and send data to cell pohone.
But ,the master device SPI wirte data is fast, the nordic will...
hi all,
since i am new to nRF24L01+ device, kindly any one provide me details regarding range that can be supported by nRF24L01+ device.i already try to find out information...
Hi,
I am attempting to create a secure BLE connection in security mode 1 and level 3.
I noticed that when I simply call sd_ble_gap_authenticate with MITM = 1 it seems...
Hi,
I would like to save the most energy when going to sleep mode. In particular, I want to turn off the radio while keeping just RTC timer on.
So, after shutting down...
Hi there,
When I tried to send data chunk (it's about 8K) to phone side according to this , the speed is much slower than 1K/s, and what's more, it's disconnected with...
Hi,
I have a problem in CRC of setup message for nRF8001,
and I already try the CCITT-16 algorithm with below conditions:
Poly = 0x1021,
Init = 0xFFFF,
Ignore all...
Hi,
I want do RSA on NRF51822. The build environment is GCC. And the develop base on S120. The RSA need 1K to do calculation. If I enable the RSA calculation, the APP may...
Is there any high-level documentation of the nRF52-DK (PCA10036) connections?
Studying the schematics, I have inferred some of the intents, like:
built-in JLink automatically...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
Hey,
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02...
Hi,
I am new to the nrf51 and I building a complex ANT application. I have part of the ANT application working but I would like to debug with printf() statements to find...
