I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
I have successfully tested the SPI master loopback example on pca10001 eval board. I have a few questions regarding a real-world scenario when there is a slave SPI present...
I'm trying to follow the instructions for "nRF51822 Beacon Firmware Documentation" for over the air firmware upgrade of the smart beacon, but I can't find the soft device...
Could this be my problem?
devzone.nordicsemi.com/.../s110-7-0-0-can-i-write-my-own-mbr
an application now starts at 0x15000 which is to make room for an extra 4Kbytes...
Hi,
I am new to BLE Development. Currently I am using NORDIC Development board (SDK Ver 5.2 &Soft device S110). I want to write a small program to establish the connection...
I'm trying to get a handle on the various ways I can implement console output on this system.
I have in the past used the retarget.c/.h code from this forum that uses simple_uart...
Hi
I use the random number generator of LE1,I have made a demo code and the code can generate a random number.As the project in attachment.
I want to get a random time...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
