Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi there,
Before I asked this question, I have searched similar question about TWI example, but it seems there were some guys looking for such example as well. Not sure...
Hello
I try make a firmware update with nrf toolbox for iOS and i have a popup with "Please enable Service Changed Indication in your firmware".
In code, I have an error...
while I'm trying to compile my code, I got an error :
".\Objects\ble_firmware_v1.axf: Error: L6405E: No .ANY selector matches main.o(i.app_error_handler). "
this error...
I wonder if GPIO could safely be used for byte writes to the OUT port.
I have an 8bit (+control signals) peripheral connected to the GPIO and so far I was doing read-modify...
I will be using a 3.7V LiPo to power my NRF52 system. As far I understand, using the internal DCDC regulator is a better choice as it can save power compared to internal LDO...
I am running the UART example with the S110 softdevice on nrf51822. Sometimes my application transmits more data than can be carried and backs up. So the main thread's transmitter...
Not really a question, but congratulations to Nordic on getting their chip onto the Micro:bit(is it the nRF51 or the new nRF52?). Looks like a cool device. I'll be hanging...
Hi,
I want to change the device name before advertising. But it looks like I cannot open the adv pipe.
I have set writeable device name both from air and from application...
Hello
I try make a firmware update with nrf toolbox for iOS and i have a popup with "Please enable Service Changed Indication in your firmware".
In code, I have an error...
I need to connect to a LIN bus and Bluetooth on the same device. I'd like to use the ARM processor on the nRF51822 based module (PTR5518) to handle the LIN bus messages. LIN...
Hi,
After looking around it seems like the I2C example that used to be in the older SDK is currently not available anymore. I was wondering if it was replaced with anything...
currently, i am designing a wearable device using nrf52 as core soc. i just found that the nrf52 has two internal regulators, ldo and dcdc converter. in my case, the input...
I'm using a nRF51822 with 256KB flash and 16KB RAM, SoftDevice v5.2.1, uVision 4.71.2.0
I can compile and run the heart rate sensor, and it will become detected by mastercontrolpanel...
Hi,
I changed the chip from 16K RAM to 32K RAM. But seems the soft device report the below error when I use more then 16K address.
Error! Line: 0290, File: src\host_core...
Hello,
I'm interested to port a scatternet tree protocol but I'm not sure about that Gazell can support all.
My mandatory items are :
Each node can send or receive...
