I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
Is there a BLE development board that supports extracting IQ data from raw MCPD ranging？ Does nrf5340dk support users to extract IQ data for the development of ranging algorithms...
hello,
I want to change the advertise time out time by BLE_GAP_ADV_TIMEOUT_LIMITED_MAX.
Is there a problem with changing BLE_GAP_ADV_TIMEOUT_LIMITED_MAX to ex. 1000sec...
Hi,
I can use nRFgo Studio via nRF5x Bootloader to update application firmware(Hex file).
It look to be using "nrfutil.exe" to create a XXX.zip file and go through UART...
Hi.
I am on nRF52 DK (PCA10040 v0.9.0, s132 SD), SDK 0.9.2 and Linux (Ubuntu).
I am currently working on the SDK's example ble_app_uart.
I am only using gcc, and...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
Hi,
I loaded S110 v8 to nrf51. Then I loaded dfu_dual_bank_ble_s110_pca10028 bootloader.
With this setup, I'm able to download my application via the bootloader.
The...
Hi,
Reading the nRF52 product specification, I see:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to...
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive these taps as interrupt...
Hello Devzone fellows :)
As you may notice, we have posted our first webcast: Interfacing with Nordic's Softdevices .
It's the first test run in a series in which we...
Anyone knows which Nordic chips they have used in this device, and do you know if it is possible to get it to Arduinio?
www.tu.no/.../345999
http://sfty.com/#produc...
Hello,
Some little compilation errors.
in ble_radio_notification.h
typedef uint8_t nrf_radio_notification_distance_t; => is no more defined in SDK but used here
...
I need to do an hybrid app like nRF UART App but with cordova. i can connect and disconnect, but i don't know how to catch the data every time the ble send.
i'm using this...
Dear all,
I make a simple test on the UART0, putting the code in 'simple_uart.c' to my main.c. When I send out a character 'A', 0x41. From the CRO timing, it appears that...
Hi all,
I am developing ble mesh network, the source code taken from this link: github.com/.../nRF51-ble-bcast-mesh . First i tested led mesh example for two boards.
...
Hi, I need to use whitelist in ble_app_uart example, What are the steps that need to be followed for that. Is device Manager is mandatory for using whitelist. Can anyone throw...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
