As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
I've made a custom board with nrf51422-QFAC, which I can program with nrf51-DK. I'm using SDK 12.3.0 and SD130, which is flashed to the custom board.
When I program the...
I'm trying to setup logging with printf() over UART and I got totaly blocked by following realy strange situation.
Let's have following very simple log_test.c:
Then...
Hi. I'm quite new to nRF programming. I successfuly solved how to compile/link/flash the software onto nRF52 DK using just a simple editor (Notepad++), the ARM toolchain and...
Wondering if there are any example/reference implementations of a bootloader for the nRF51822 that support Device Firmware Update over both UART and BLE? We've got the BLE...
Hi,
I have met problem when apply dfu of nrf52810.
I used dfu sample of 52810 from devzone link: https://devzone.nordicsemi.com/f/nordic-q-a/28471/about-ota-for-nrf52810...
I met a big issue when implement the voltage level switch. I used nRF52832's SPI to communicate with an ECG sensor which has 1.8V SPI. The issue is that, 3.3V signal from...
Having just got the DFU functionality working I got the task of trying to add NFC functionality to the application. The code side was not a problem since I got a c and h file...
According to the BLE 5.0 Specification :
"The Link Layer shall use the primary and secondary advertising channel
indices as specified by the Host, and the used primary...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
