Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I'm planning using nRF52810 for a new product to reduce the power consumption.
But i worried whether old smartphone with Bluetooth4.0, like Iphone5s can connect with equipment...
I am dealing with the nRF24L01 to develop a remote controller. When I read the specification, I found a specification item, called C/ICO, with a typical value of 12dB in the...
hello,
I'm trying to send long (73B) data on a given characteristic using Android client as the central.
I well received:
USER_MEM_REQUEST OK
> #define...
Hi to everyone!
I'm following this guide to learn how to use secure DFU on a nRF52832DK board.
All steps have been done successfully, or I think so, until I reach the...
I want to find the agent of China, please, thanks
About Bluetooth and 2.4G, nRF52840/nRF52832/nRF52810
(The agent can provide some technical support and sales)
Can someone please explain the below line mentioned in NRF5 Serial port abstraction layer documentation.
Do not use synchronous API (timeout_ms
parameter > 0) in IRQ...
Hi there,
I want to flash nrf51 firmware from another MCU which is connected to nrf51 with UART interface.
I have seen dual bank serial bootloader examples, in that firmware...
Hi,
I know this has been touched on in other posts but I can't find a definitive answer.
I am making a product that sends data from a handheld joystick to a base station...
Hi All!
we are trying to tune Antenna use DTM over UART from examples.
It is works fine for AAAA IC but doesnot for AABB IC.
Why, what's possible problem?
thx...
Hi everyone,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I need to develop a repetitive task with 10 Hz frequency...
Hi
I am trying to use the serial bootloader to upgrade nrf52 application, but I get verification failure.
I am using nrf52832 with SDK 13.0.0 & S132 SoftDevice v4.0...
Hi,
(1) I look for some methods that suggests is application flag to record. but I set this ble_adv_on_disconnect_disabled = false;. How do I check ble state when disconnect...
Hi
I'm trying to write data to flash and access it via declared const variable.
I can't use UICR because we are on NRF51 and this does not allow to change data in UICR...
Hi All,
I have this problem with using the ESB + Timeslot example from Github .
The interval of the ESB TX Transmit is depended on the advertisement interval I configure...
I am looking into registering product with Bluetooth SIG, and was reviewing this document:
www.bluetooth.com/.../qualification-listing-fees
There I found the item "16...
