I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi
on nrf52832 ble_app_uart how can change MTU size and LL payload size?
have any source ? or example ?
or any change MTU and payload example ?
( for BT4.2 ~ BT4...
Hi,
I'm using SDKv14.1 on nRF52810. I doing the DFU according to the ble_app_buttonless_dfu example. When I use sd_ble_gatts_service_add to add service UUID in the ble_dfu_buttonless_init...
By testing the source example of throughput example of S132, it is known that throughput is mainly affected by four factors.
1, ATT_MTU
2, DLE
3, Connection event...
Hi Nordic team,
Currently our company under developing the product using NRF52840 + S140 Softdevice.
Now we prepare to list our product with Bluetooth SIG but after...
Hi,i have some problems at fds in sdk14.1 ble_app_buttonless project.
1,fds_register() & fds_init();
2,fds_record_write();
3,fds_record_find();
4,printf the record...
Hi guys,
Right now, I'm trying to do some throughput measurements via the experimental ble_app_att_mtu_throughput example. This using the SDK 14.2 and S132 on two nRF52832...
Hi,
I have seen some curious behavior with the FDS module. I'm using nRF5SDK 14.2.0 with s140_nrf52840_5.0.0-2.alpha, with FreeRTOS. In short: In some cases it seems that...
Hi!
I want to get infinite advertising.
My advertising gets timed out in 180 sec.
I have set to Fast Advertising Mode.
Below is my code
static void ble_evt_dispatch...
Hello,
I'm following this BLE services tutorial . I have added the functions required to create a service.
In the our_service_init
void our_service_init(ble_os_t...
Hi guys,
Currently, I am developing a application on nrf51822 which requires writing values on flash to store in case of power down. However this values need to be updated...
I have a nRF51822 smart beacon kit and a ST-LINK V2. I read the documentation found on nordic's website, downloaded all the programs that the documentation requested etc....
Looking through the ESB implementation in SDK 14.2, nrf_esb.c I notice it uses
#ifdef NRF52
on several places. In nrf.h, the "old" NRF52 gets re-defined as NRF52832_XXAA...
I tried every configuration I can think of to reload firmware on the DK with JLINK drive when PPK is piggybacked. The only way I can get the firmware to load on the DK is...
Hey, I'm running the ble_app_hids_keyboard example. I would like to modify it so that once I have a connection to a device I can press a button and go into advertising mode...
I have questions about nrfutil's latest.exe. Dose it able to do OTA DFU over BLE for every SDK version's firmware?
I have been trying do OTA DFU using Master Control Panel...
