i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
Hello everyone,
I am trying to implement a bootloader to my application to be able to enter in DFU mode.
I am using nrf51822 (32KB ram 256 flash) and s130.
I have taken...
My understanding is that the nRF51 is known to need a fairly stiff external pull-down resistor on SWCLK to avoid noise putting the chip into debug mode. I note that the nRF52...
I'd like to know how to implement a bootloader for the Nordic SoC nRF51822-QFAA-R in order to boot the softdevice and some firwmare. If will be great getting an application...
Does nRF52832 have battery monitor?
I can't find in the datasheet if there is an externarl circuit to monitor the battery. I'm using a CR2032 coin cell battery.
Tha...
Hi,
I'm developing some firmware that will hopefully run on a few different kinds of nRF52 device.
Is there a way of detecting if the DC-DC converter's inductor/capacitor...
Following situation:
My device acts as central (connecting to ble sensors) and as peripheral (transmitting and receiving data from mobile). Several services (Heart Rate...
Hello,
I followed this tutorial:
devzone.nordicsemi.com/.../
and added the RTT files to the project, however, after I compile i get this message :
and when...
Hi guys,
I am using the RFduino nrf51822 chip. I am using the TIMER2 interrupt and it works fine. But when I try to use the BLE along with the timer interrupt both don...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
hi,
i have PCA10028 dk board. i want to flash code in this board using dfu. i have generated Zip file(both soft device and application(example ble_app_hrs example)) using...
I am using this DFU library github.com/.../IOS-DFU-Library . On iOS 10 while processing DFU I receive error RemoteInvalidState in didErrorOccur method with description "Device...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
Hi everyone!
I'm using the nrf_soc API for get random numbers from the rng and erase and write the flash memory.
In my code, I include the nrf_soc.h file, in the header...
