Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am using S130, and I try to write an very simple program, when I push button_1 then it read ADC and print it our by UART.
So, write a "nrf_drv_adc_buffer_convert" code...
I connect to nrf51 DK board and PC using USB. I used RTT Viewer to see RTT log output.
But when I try to compile and download from keil to the board, I got several WARNING...
All,
Can anyone tell me what is the fastest time that a ble SD (5.x / 6.x) running on an nRF51 can (re)start advertising from a disconnect. Basically looking to do an ...
I am not able to connect Garmin Edge or SimulANT to nRF51-DK. Neither sensor nor receiver seems to work. Just looks like there is no RF.
Examples tried:
power_only_sensor...
Dear Sir,
Here I test the ble_peripheral example "ble_app_uart" (Softdevice 8.0) with Kail MDK ARM 5.20 environemt on the PAC10028A board.
I found it's not stable and...
Hi,
I'm having trouble increasing frequency of data TX using ble_app_hrs example on PCA10028.
I tried to increase the TX frequency of heartrate data to 100ms by configuring...
It seems that the nRF52 Development Kit mis-handles extended hex records. If it has type "04" records (extended linear address), it works OK, but if it has type "02" records...
We have an optical measurement system where we need to pulse LED and sample a phototransistor precisely during the LED pulse. The rate of sampling is 1 kHz and we plan to...
HI i need help in sending a data value of 700+ continuously
1)May i know how should i format my data packet to suit the current 20 bytes of data sent through BLE
2)Is...
Hi,
I am working on application in which I want to send 1000 or more samples using SAADC and BLE over standard master control panel APP of Nordic. For sampling analog data...
I'm trying to fully understand how DFU works and am going through the nRF5 SDK v11.0.0 example bootloader ( dfu_dual_bank_ble_s132_pca10040 ) and app ( ble_app_hrs_s132_with_dfu_pca10040...
[summary]
When I update app by Keil μVision, RAM setting is reflected correctly, but when I update app on OTA, RAM setting change is not reflected.
[condition]
Old...
Im trying to read flash memory ( N25Q032 ) identifier using SPI (NRF52) but then eveytime I try to read a register, the output is always zero, I tested with oscilloscope and...
