Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
On the nRF51 DK there is a MM8130-2600 connector. I suppose it is used for connecting coax cable when tuning the antenna(?)
The connector is quite expensive, though. Is...
Per the name "UUID" and the very limited background knowledge that I have, it appears that a particular device can have its UUID assigned by its manaufacture, who bought the...
Hello.
I am developing a BLE application on NRF52832 using Nordic SDK11 and S132 softdevice. I use Linux PC as a BLE host device, and can pair & bond the NRF bluetooth...
Hi there! I'm using the nRF Toolbox's UART to test the receiving of my data stream. I'm trying to send a data array collected (from spi) in my main loop and send it via UART...
I am studying the iot-sdk of nordic.
Now, as I have shown in previous questions, I can not detect the device under the linux system according to the toturial in iot.
Now...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1?
About problem:
...
Hi,
I've been trying to add the option for BLE HID to the Espruino JS interpreter on nRF52 - it's something that ideally would be switchable at runtime.
After having...
Dear All
In my application we could not use the ADC inside the nRF51822 because 10bit are under our requirements. But now with the new nRF52xxx with a built-in 12bit ADC...
Did anyone manage to build project on Eclipse with some nRF52 BLE application for HomeKit?
I have found only one project from aanon4 but I cannot even build it.
Sometimes...
