Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Using nrf51422 in KEIL. I am verrrryyyy new to this type of programming. I have been looking at multiple examples within the nortic github to find how to input analog reading...
I started Heart Rate Monitor app "ble_app_hrs_pca10040_s132" on nRF52 evaluation kit (nRF52832). Everything work well when I connect with nRF evaluation kit from Android devices...
Hi!
I just got my PCB with a Telit BlueMod+S42 Module on it (nRF52832).
I' using the LESC feature and ist works properly on the PCA1004 and on the Telit DevKit (same Module...
Hello,
I'm working on a bootloader based on the example of SDK13.1. I want to add two more characteristics to the DFU service, but after I add them, the nRF Connect app...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
The file nRF5_SDK_1 4.2.0_17b948a/components/libraries/util/app_error_weak.c requires the following modification to correctly compile: Add: #include "app_util_platform.h"...
Hi,
I'm currently using SDK v14.2.0 and I'm attempting to merge the buttonless DFU bluetooth example into the bluetooth template project within the Eclipse Oxygen environment...
Hey Guys,
I have 3 tasks running on FreeRTOS, SDK v14.0.0. In each task, I want to use SEGGER_RTT_printf() to debug.
I currently just call SEGGER_RTT_printf() without...
I have two nrf devices nrf51822 and nrf52DK, In nrf51822 i'm using S110 and i had created a custom service with 10 characteristics. If i connected to nrf connect i can able...
Hi,
Is it possible to make realization of this protocol ( wiki link ) with softdevice? After reading forum I think "more no than yes" because softdevice blocks CPU and this...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
