Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am using the PPK with SW v1.1.0 on a windows virtual machine on my mac. I'm testing custom hardware using the PPK regulator to supply power to my hardware.
There seem...
Maybe I understood something wrong, but I wonder if it is possible to have the nRF52840 handle file transfers like it does with the firmware hex-files.
Say, I want my nRF52840...
I am facing some issue, I am using HM10 ble module as peripheral and NRF52832 (Redbear NANO v2) as central device. I using SDK "nRF5_SDK_12.3.0_d7731ad" and example program...
Hello, deavteam. This is MANGO.
The Capacitive Touch on the nRF52 series blog post is really impressive.
I'm planning to start a haptic driver project using TI's DRV2605...
Hi all,
I am experimenting an issue similar to this guy --> devzone.nordicsemi.com/.../
But I have my project in two different branchs one using Peer manager and multiple...
when i use sdk14.2.0 and nrf52810 nus service send data， When the app transmits data for some time, the app prompts to disconnect, but the slave does not log any log prompts...
Still playing with my app. Since RTT (or whatever it was, when printf was printing info to segger debug console) was ruining the debug process, I just switched off RTT and...
Hi All,
I am new to nRF development and purchased the nRF51-DK (PCA10028). I have successfully experimented with the examples for ble_app_uart and lpcomp. My Application...
I have the beaconing/lightserver example working and being provisioned by the serial example. How might I now change the advertising of the beacon using the PyACI PacketSend...
Hello. I have a ttl converter ( https://goo.gl/images/uFSPHN) . Can I write a hex file through it? What are the possibilities to program so as not to buy a debug card?
Hi,
If I need to get RSSI updates while the peripheral is in connected mode, I need to call sd_ble_gap_rssi_start() just after connection has established. Then the RSSI...
Hi,
I'm using s130, nrf51822 and sdk 12.3.0
I'm wondering about advertising timeout units and it's range... BLE_GAP_ADV_TIMEOUT_LIMITED_MAX is 180 sec... In ble_gap...
I hope Nordic Semiconductor is working on #BluetoothMesh provisioner & configuration App like Silicon Labs already has.
But could anybody inform me, how you are going to...
Hello,
I currently have a PCA10036 EVK with softdevice SDK1
Following below well written tutorial, I have modified ble_app_hids_mouse example main.c file as in attachment...
