I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
Hi:
I use SDK7.2.0 encountered a problem when I was disconnected, has reached the maximum number of bonding, I want to remove the first bonding information. I do not know...
when i use sd_ble_gatts_hvx() to send data,it cause a HardFault error。 when i trace the sd_ble_gatts_hvx() function,it will run to 0x00016432,in there will be compare two...
Hi,
I use sd_ble_gattc_write function to write to my peripheral with my central device. I'm sure the settings should be right but i still can't see any change on peripheral...
hi,
i have successfully entered the dfu mode many times and could change the applications and reenter the DFU mode.
But then i tried loading the softdevice at "nRF51_SDK_8...
Hi, All,
I am currently developing with nRF51822AC. Due to some issue, we would like to replace the current 16MHz crystal with a crystal other than this frequency. We would...
softdevice 8.01 s110
device nrf81522
hts example,add three ch adc,lcd eg.
phone : HTC one M7
app:nrf tools HTM
when try to connect the device by BLE, when recive the...
Hello!
I am trying to run example uart project (uart_pca10028) on PCA10028 development board. When code is loaded to the microcontroller it signalizes error - all leds...
Hello All,
I am working with a pre-programed PCB; the main components of the are a nRF51822 chip, a GPS, and a GSM. I am using a J-link to communicate to the entire board...
