The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello,
I try to modify the advertising initialization to advertise only my custom service (BTS_UUID_SERVICE ). Objective is to hide (just during adv) others sig services...
Hi,
where could i find detailed current consumption and timings (wake-up, rx, tx, power down) in connected mode for RF51822, in order to compute average current value for...
My device :
nRF6310 Rev 1.4(nRF6700)
nRF2722 Rev 2.2
I will use those devices to test RF communication between nRF2722 and nRF51822. Software environment is...
Hello,
I am playing with the s110 ble_app_proximity example.
As I do not want to store info in flash, I do not want to use the bond manager, that stores data in flash...
I'm currently using a combination of the GNU ARM Eclipse plugin and the unofficial pure-gcc Makefiles to build my nRF51822 code. The build works fine with the pure-gcc Makefiles...
Hello everyone,
I want to create a real-time wireless sensor network. There are 8 sensors in the net. I use two nRF24LE1 as receivers to recieve the datas stimultaneously...
Any idea what the max SPI slave clock frequency is on the nRF51822? The product specification (page 46, v2.0) says the max SCK frequency is 2MHz, but I was wondering if any...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
