Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi,
I get the error "[DFU] Remote DFU error: INVALID OBJECT. SD busy? Retrying...." when attempting a firmware update over Bluetooth.
The bootloader, application and the...
Hello,
I'm working on nRF52811, SDK16.0, Softdevice 7.0.1.
Using the pwm_driver example in the SDK, I'm trying to run a simple PWM for an RGB LED. Following is my simplified...
Hello,
I am trying to develop a product on a large scale. I need the last 4 digits of DEVICEADDR[0] as the advertising name for uniqueness. But I am not able to get it working...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
Hi,
I'm using saadc library to measure the voltage on nrf52832 DK. also I'm using soft device s132 on the project. I have several questions and will list below,
I want...
Dear Team,
I am trying to use nrf53840 USB dongle as sniffer. getting following error.
Reopen device failed: Timeout while waiting for device FAC66FF88C25 to be attached...
hai ,
In my application to connect 5 peripherals with central and here i am connecting with device names
static char const m_target_periph_name1[] = "Nordic_Blinky1";...
I try to send NRF_DFU_OP_PING reqeust ,then received BLE_GATTC_EVT_WRITE_RSP message. but write_rsp.len is equal to 0,.I can see gatt_status is BLE_GATT_STATUS_SUCCESS. I...
hai ,
i my application i should connect 5 more peripherals with one central .
at first i connected with peripherals mac id , mac id hard coded in central
in central...
Hi,
Is it possible to be notified when the device is entering/exiting idle? All I can see is that idle thread calling k_cpu_idle which doesn't appear to have any hooks?...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
I want to connect and get data multiple peripheral to a single central device.
I used this example https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
...
