We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
Hi,
Platform: nRF54L15, SDK 2.9
The application is Matter + BLE. CONFIG_CHIP_DFU_OVER_BT_SMP & MCUBoot are part of the configuration. As soon as we enable the BLE...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
Hello,
We are using the nRF52832 and 2G(GSM/GPRS) module to build up one IoT product. We got a disconnect between nRF52832 with other master instance(mobile phone APPs)...
Using Softdevice s140 v6.1.0 nRF5 SDK v15.2.0
I am trying to write to the flash, here are my read and write functions:
Two problems:
The write function does not...
Hi,
I've added an instance of the Generic Power OnOff Setup Server to an element and I can see it and all the models that it extends, i.e. (Power OnOff Server, DTT Server...
Hi all!
I'm trying to run the light_switch example (client and server), and i cant complete the provision process.
I'm using my phone and Nordic app for provision, when...
Hi.
I just wonder how can I send string message through ble.
I will use raspberrypi as server. You can check whole code below.
It works well with computer bluetooth...
I am working on nrf52SDK. For my curiosity i wanted to know the BLE stack version.
Is there any calls available to query the soft device(S132) to know the BLE stack version...
Hi all,
I have a very strange problem with the Buttonless DFU service. For my project we have two different builds, one debug and one "release" build. The debug build sets...
Lately with 2 different nrf91DK boards I have, I can't program them unless I do a full erase first.
I did see this post here: https://devzone.nordicsemi.com/f/nordic-q-a...
I am shopping for a Bluetooth module that will accept Bluetooth streaming from a personal device, supporting A2DP V1.3 minimum, decode it, and output an I2S stream. Many Asian...
Hi,
I have a project running on a custom board with the nRF52810 populated and I make use of a GPIOTE input interrupt. The code works fine for the nRF52810, but not when...
Hi
There are two things I need help with. I am using Segger Embedded Studio on Linux(16.04) and SDK 15.3
1. I am using nRF52832 DK to debug and flash to external(custom...
