Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Dear Nordic Developer Zone,
I have incorporated LESC in the following development environment. 【Development environment】 ・nRF51822 ・SDK12.3
The following function is executed...
Hi, all
I'd like to get the whole thread network topology (like nRF_TTM does) on raspberrypi, can this function be realized with wpantund or wpanctl?
Is "wpanctl mfg....
Hello,
I am attempting to integrate FOTA (HTTP Application Update) into a Thingy91 project on top of the LTE BLE Gateway example project.
I am on nRF Connect SDK v1.1...
Hi,
How many SPI slaves can I connect to nRF52832 as an SPI master?
I would like to know the maximum number of SPI slaves which can be connected to nRF52832 as an SPI...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I am using NRF52832 for development without bluetooth SDK, NFC and RTC.
I am using a development board with SPI and a slave device that can communicate normally (using...
Hello,
Most of the outputs and LTE Monitor use by defaut an UART on DK. Problem on custom boards, for cost limitation, UART is not always present. Probe connector is so...
irq init as below:
I use port event, and muti-gpio irqs. Irq gpio connect a sensor`s irq pin.
I detect irq gpio level in irq_Handler(), high level is my need, the...
Hello All.
I Need help ... first time use "nRF52840"
Goal of this project is "record voice with digital mems mic and play that voice using speaker with i2s"
First...
Searching through the forum I found this guide.
"Getting started with Nordic's Secure DFU bootloader, a step by step guide"
https://devzone.nordicsemi.com/nordic/nordic...
SDK 16.0.0
nRF52DK
ble_app_hts example
The ble_srv_is_indication_enabled always return false no matter in the ble_hts_is_indication_enabled function or in the on_cccd_write...
Hi, im usinh SDK V 15.3
i was following the tutorial to add buttonless dfu to my application code
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am a newbie and need some help deciding the path to perform the following requirement. Any help is appreciated.
Requirement:
I have Rigado BMD-350 module currently...
Hi,
I have a nRF52840 DK (PCA10056 v0.9.0). I tried the long range (Coded PHY) but it throws an error and didn't work. I read in nordic forums that the chip revision should...
