nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi everybody. I know that it is complete standart question, which has many asks and solutions here. I'm quite new to bootloader management stuff. So asking about some targeting...
Hi,
I am fairly new to BLE application development on NRF52.
I have a temperature and humidity sensor TH02 and I have interfaced it by making essential changes in TWI...
I found a function, sys_reboot() that apparently reboots the nRF9160. In order to use this function, what must be configured and what are the correct .h files?
Thanks
Hello,
I am trying to configure my nRF9160 v0.8.5 dk for current measurement and found out that SB 44 is missing on my kit. As the user manual suggest that in order to enable...
Dear DevZone team, I am using Thingy91 in NB-IoT mode because I am located in Germany. Last week I managed to connect it to the nRF Cloud by updating the firmware (thingy91_nbiot_legacy_pco_v0...
Hi,
I have multiple sensor data that needs to be recorded in separate files. This data is being collected in parallel. Using the FATFS xample in SDK 15, I am able to write...
Hello all,
I’m trying to connect my nrf51dk (board 1) with a CSR8670 (board 2) using GAIA services and characteristic.
On BOARC 1 i have implemented “Central HRS” beacause...
We made the test with your demo SDK on the board :
PCA10056 1.0.0 2018.46 PCA10056 1.1.0 2019.26
We modify the code to gate the trace ( see the attach file)
And the...
Hello team Nordic,
Example ble_app_rscs_c is working well with my pca10056, im using it to scan for advertising reports. To do the same with pca10059, im trying to merge...
Does the nrf52811 temperature peripheral do automatic linearity compensation? The product specification 1.0 says: " Linearity compensation can be implemented if required by...
I'm currently unable to build the asset_tracker for Thingy:91 on Segger Embedded Studio - using nrf9160_pca20035ns for the nRF Connect SDK Project
Do anyone have an idea...
Dear Team,
what is the way to do it in Zephyr?
I have a signal up-to 10kHz, what is the best way to keep the counter in the background?
Thank you and best
Oleh
In the getting started assistant App
When I run:
pip3 install --user -r zephyr/scripts/requirements.txt
I get this as the error:
However, when I run
pip3 install...
I am doing power consume estimation, need to know detail of RF activities, is there any way to get the total send/recevie bytes of RF? or just simple tx/rx counts? My project...
