Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
I have been able to use external flash with Octal SPI mode on an nRF54H40-DK:
❯ west build -- pristine -- board nrf54h20dk / nrf54h20 / cpuapp zephyr / samples / drivers...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
After compiling the SDK 15.2 ble_app_hrs_freertos_pca_10056_s14 example in Segger Embedded Studio there are a number of repeated warnings:
"configTICK_SOURCE" redefined...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
Hi,
I am trying to use the SSD1306 display with the nRF9160 DK.
I am using the code as is shown here
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples...
hi, thanks for this tutorial : devzone.nordicsemi.com/.../ble-advertising-a-beginners-tutorial
i'm trying it on my nRF52840 devkit board.testing it with nRF connect application...
I have a nordic ble dongle. I want to interface it with an external microcontroller via usb. Is there a set of usb commands that can invoke the softdevice api's in nordic...
Hi,
I have a question about how IPv6 addressing works in an OpenThread network. I read in the OpenThread website that the ML-EID is also known a Unique Local Address (ULA...
Hi,
So I've made a post that I was unable to debug my app with the bootloader. But I've found out that it is entirely different problem. So my app is runnning whit FreeRTOS...
I'm trying to sample analog input but there is no value after sampling.
I tested the input by configuring it as digital input and it worked correctly.
Below is code. Any...
Hi,
I totally forgot about the voltage level difference between the debugger and the dongle and connected them. It was somehow working in some cases but not consistenly...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I want to log the application error data log into the internal flash(1MB) using the mesh example. I found that there are two ways of writing 1)FDS 2)Flash Manager. I...
hi ,
i am using nrf52832 dev kit , using which i am capturing accelerometer data from LIS3DSH for an RTC interrupt of 2 minutes, i.e., for every 2 minutes it should capture...
Hi
I have nRF52832 development kit and a few custom boards. I am planning to run some Mesh examples using the boards. But, almost all the examples require at least 2 Development...
