Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
NRF51822 RM 3.0 section 14.1 states each GPIO pin has DETECT, but where is the register to read per-pin detect? From the manual: "Each pin has a separate DETECT signal, and...
Hi,
Now, i want to use SAADC with softdevice of SDK15.0 to make a beacon program.
I migrate SAADC example in nRF5_SDK_15.0.0_a53641a\examples\peripheral to beacon with...
Hi,
I am using nrf_sniffer_2.0.0-beta-2_10Sep2018_3ef662e for capturing ble mesh packets but i am finding LE LL packets of my node with mesh beacons in my wireshark. Even...
Hello, I am new to nordic sdk and tools. I am planning to develop a nRF52840 DK based sensor device that reads I2C temperature sensor data ad broadcast it periodically. Also...
Hi,
I'm testing the BLE_UART example : <InstallFolder>\examples\peripheral\ble_app_uart . For this, I use the nRF52840 with SDK 15.2 and s140 softdevice.
I would like...
So I am using nrf52832 and making a whole new app in ios. My objective of the app is to get the sensor data (specially motion sensor data and accelerometer data) which is...
Hi,
I am trying to add app_uart into the heart rate sensor example. I called uart_config(); in the function function, but when I open the serial monitor, The errors shown...
Trying to build the unmodified light_switch_client_nrf52832_xxAA_s132_6_0_0.emProject from a fresh download of the Mesh SDK.
SDK_ROOT set & successfully tested as instructed...
Hi Team,
This is more like a generic question.
I have 100 beacons and I want to test them all simultaneously kind of a bulk testing.
What are the possible candidates...
Hello,
I would like to use the hardware crypto engine that is a part of nRF52832 chipset. I understand that the access to it is restricted as SoftDevice uses it. I wonder...
I am running into these 3 errors while compiling my program. I tried fixing sdk_config.h.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol app_uart_init (referred...
EDIT: I have added the battery data in percentage to scan response manufacturer specific data. Is that the only possible way?
Hello,
I am working on a beacon application...
