I am using the following version of nrfjprog on my Windows 10 machine:
nrfjprog version: 10.24.2 external JLinkARM.dll version: 8.44a
Most of the sub-commands work with...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
Hi
my idea is to open and close pipes identified by BLE address of device.
Currently I enable ESB on BLE disconnect using timeslot API.
How can I do this "on the fly...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...
Hi,
is there any way to connect at the same time multiple devices with Android/iOS nRF UART app to an nRF52832 with ble_app_uart example?
I was thinking about adding advertising...
HI all,
I am setting these parameter as follow in my ble_app_template sample.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) /**< Minimum acceptable connection...
Hello everyone
I'm the proud owner of a nRF52 Prev. DK and trying to get my project to work. I would like to sample 3 to 5 analog signals using the ADC on the DevKit, followed...
A beginner's question.
I am using UART over BLE to send data out.
As codes below, ble_nus_string_send() works and continuously sending data out, with the Wireshark's...
I have some problem when I implemented 52832 dfu.
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio...
