I have recently purchased nRF52840 dongle which I wanted to use as a ZigBee sniffer. I bought it on AliExpress and it supposed to be original Nordic board, but it turned out...
Hi,
I have a project requirement to interface with HART, which is a protocol that specifies odd parity for UART. I recently found out UART odd parity isn't supported on...
Hi Nordic team,
I am working on nRF5340 and trying to enable MCUboot serial recovery DFU in single-slot mode with both signing and encrypted images.
Environment: 1. SoC...
Hello Nordic Support Team,
I am experiencing a startup issue with the nPM1300 PMIC. Below is the summary of my hardware configuration and the behavior I am observing:
...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
I have been using SDK 11.0.0 in a gcc/Eclipse environment successfully.
I can download the ble_app_hrs_pca10040_s132 example to the dev board and successfully run the HRS...
I am developing a script that runs on the nRF51822/ BLE nano to connect to other devices using blue tooth low energy. To do this currently I am looking at the heart rate example...
I am testing the ble_app_uart and nRF UART app. When I transmit the message from mobile phone to the module. The module can always receive the data and display on the terminal...
Here's the original error:
compiling app_util_platform.c...
C:\Keil_v5\Nordic_SDK\nRF5_SDK_12.1.0_0d23e2a\components\libraries\util\app_util_platform.c(17): error: #20...
am trying to use SPI with nRF 52832.
So I implemented spi_master.c which was used in nRF 51822.
However, it does not move hard.
The length set by SCLK does not come out...
Hi,
So I'm fairly new to programming the nrf51822 and using the Nordic platform.
I'm currently using the nrf51822 Waveshare DK. I have setup JLink5.1.2, nrf5_MDK_8_5_0...
Hello,
I am using SD 130 on nRF5 with SDK V12.1.0.
I want to write to a characteristic using the android debug app (nrf connect).
This is my code for the characteristic...
Greetings,
As mentioned in this blog post, GCC compiler -flto flag isn't mysteriously present since SDK 9.
devzone.nordicsemi.com/.../
Any specific reason for this...
Hello,
I use a SparkFun programmer to flash a nRF52832, once I flash my board (with the program below), I type in my terminal : "JLinkExe -device nRF52 -speed 4000 -if SWD...
I have many peripherals, dealing with each of them individually will be very ineffective. The peripheral has no buttons, but it has a display.
Questions :
For security...
Hi,
In my application of interfacing SD card with nrf52, I am using SAADC to sample the input signal at 1000 samples per seconds. These samples I am combining in 84 packets...
I have set up ble_app_uart along with gpiote and spi. When I first trigger the GPIOTE event the MCU is supposed to go to sleep after, but it seems to keep running in the main...
Hi Everybody!
I'm trying to integrate a buttonless dfu into my application but I'm not able to get even the provided example in SDK 12.2.0 "experimental_ble_app_buttonless_dfu...
Hi,
When calling app_sched_event_put inside the same hanler i am exit to main for(;;)
The main loop
for (;;)
{
nrf_drv_wdt_channel_feed(m_channel_id);
app_sched_execute...
