Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hey Guys,
im working on some sort of application transport layer for ble and have some questions to better plan what i need and what is kind of redundant.
Is it correct...
Hello everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
I'm using nrf52 with SDK version 12.0.0. I'm trying to use the FDS for my application. I used one of the existing fds example from link fds_example .
With this example...
Hello,
I am a bit lost, after concluding the application part of my project I try to approach the ble part.
I read the "Getting started with bluetooth low energy " and...
Press down PWRON1 give rise to Q2 and Q3 conduction, the 51822mcu power on and IO send a hight level to PWRON,to keep VCC_nRF.
At this time press a lot of button will not...
Is there an unsecure version of the bootloader? I'm looking for something that will take anything as an upgrade.
I figure if I'm stuck in the bootloader anything is better...
I want to set up a rPi3 as edge router for 6LowPAN over BLE. Ideally I would like to have random devices (users) come and go by dynamically connecting to the router. Same...
i am using eclipse IDE. while flashing my code to nrf development kit it is showing like this and also in the console it is showing that flashing is done.
console:-
SEGGER...
Hi
For new BLE project we planing to use slave that allow few (3-4) connection at the same time. i.e After the master (phone) connected to our slave, the slave continue...
Dear Nordic Developer Zone,
At this time, I am able to program nRF51822 chips using the nrfjprog software : great.
I plan to use nrfjprog software driven by a custom...
Hi,
I'm tring to installing micro-ecc,but I don't know how to get the mircro-ecc GitHub repository.
I had read the guidance like the following,but it couldn't help me. ...
Hi all,
I wrote a small python script on top of the pc ble driver bindings and ran into a problem when deploying the script on a new pc:
c:\Python27\Scripts>python.exe...
I changed ble_app_beacon example main.c APP_COMPANY_IDENTIFIER 0x0059 to 0x004C for nrf beacons app can detect NRF52832 beacon on my Iphone. What can I do to detect beacon...
