Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
My setup:
NRF52DK;
Keil 5.22.0.0;
nRF5_SDK_12.2.0;
S132 3.1.0
While trying to use ble_peripheral\ble_app_template\pca10040\s132\arm5_no_packs I decided to modify...
I'm sorry. I closed this question and can't reopen. I need more answer.
If I solve all problem I'll close this question.
As you mentioned I'll try HW version modification...
I've just noticed that it's possible to call ble_advertising_init() and ble_advertising_start() with params that are quite conflicting.
ble_adv_modes_config_t advertising_modes_config...
Hi dear Engineers!
We want to add Eddystone compatibility to the device.
Is it possible use nRF52 silicon radio ?
How I understand, it is not compatible with any SDxxx...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
Hi ,
I am trying to interface SD card with nrf52. For this I am using fatfs example of new 12.0 sdk. I can able to write the data to file but when I am taking the data...
