I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hello,
Now I am using nrf51822 with PCA10004 EK board. And the custom board we are using is BL600-SA module. As BL600 can be used with nrf SDK and softdevice, Can I use...
I have a Bluetooth LE dongle and I have also a BLE device that I want to communicate with.
On the BLE device there are a several services like Cycle Power (0x1818) and Device...
I'm using the Ulink-ME tool in order to program/debug my custom board based on the nRF51822 device. The problem I have is that sometimes the flashing procedure is working...
Hi,
I do some function base on the ble_app_uart peoject and using the S130.Now I want the device disconnect the connection once it receives the disconnection command from...
We are looking into upgrading to the newer nrf52 SoCs from the current nrf51s. From the looks of it, the SoftDevice S132 is still in the alpha stage of design and validation...
Hello,
I am using SDK 9.0 and softdevice 8.0 and testing on Evaluation board.
I referred the i2c example driver suggested by Torbjorn in this link
I wrote a simple...
Hi,
Are there any plans to release the nRF51822 sniffer source ? I can only see ihex binaries in search results. I am developing some dev boards using nRF51822 xxAC and...
Hi,
I've read through several posts on this excellent forum for nRF51 on audio.
But, I have the new nRF52 Dev Kit and would like to use an analog signal from a microphone...
Hi Gentlemen,
i want to pair my mobile(central) with peripheral device by entering passkey
note: No input or display on peripheral device
suggest the method with sample...
I use 51822 HW TWI to become master.when i send the first byte(Address+write or read bit) to sensor,the event TWI-ERROR is set.Who can tell me, what is the cause of this event...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
Hello everyone,
Please forgive my continued naive questions. This is my first embedded-systems project.
I have been working with an nRF52 development board and SDK 0...
I've used the very well written IOT examples with no problem on a R PI, Ubuntu PC, and BBB all with 3.18 or 3.19 kernels. I've moved to 4.1 and 4.2 kernels and the behavior...
