Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
Hey guys,
I have a little problem on a new board comunicating with a MPU9250 sensor.
Chip version is nrf52832-QFAA-BA
GPIO PINS Used P0.20 (SDA) and P0.21 (SCL)...
The S332 v0.6 has been released and it is supposed to be compatible with SDK11. My concern is that in the release notes of SDK 11, it says "Temporarily removed support for...
I tried the above example but it hangs here:
while (ser_sd_transport_is_busy());
Not sure why, I'm using GDB to step thru code, and it appears always busy...
Is there...
Device: NRF51-DK
I'm using GDB+OpenOCD to step thru code and it appears that the nrf51 resets itself after calling:
SVCALL(SD_BLE_GAP_ADV_START, uint32_t, sd_ble_gap_adv_start...
I want to make rs485 communication with nRF51822. I gone through the UART code, there CTS , RTS pin are required , but for my case tx, rx,rx enable is enough, and also shall...
