I'm hitting a wall with implementing nRF7002 + nRF52840 without Zephyr.
I've worked with nRF52's for about 8 years now and on about 30+ products, all using the original...
Hi, I am currently migrating my project from nRF Connect SDK v2.5.3 to v2.9.0 / sysbuild.
Unfortunately, my devicetree configuration for a mcp2515 CAN interface is not accepted...
Hi
I've recently switched to NCS v3.0.0 because it now has TDM peripheral support for nRF54H20, however since there is no specific examples to use TDM, I've used I2S example...
Hi Nordic Team,
I am using NCS v3.0.0. I have added tamper detection under the General Diagnostics cluster (0x0033) and update the ActiveHardwareFaults attribute (0x0005...
Hello,
I have some code running on an NRF52832 using NRF Connect SDK 2.5.1 which initalizes my BLE with a random private resolvable adress so that I can easily reconnect...
Hi, Any one kindly suggest and Chip based antenna for the Thread + BLE and Wi-Fi + BLE protocol in NRF54L15 protocol. Also kindly suggest the PCB based antenna for the Thread...
Hi,
We are currently in the research and development phase for a new line of IoT devices designed to work over the Matter protocol. After thorough evaluation, we found the...
Hi all,
I try to reduce the power consumption of my GZLL host (RFDduino/nRF51822).
I use the Arduino IDE to program my RFDuino.
My Idea was to synchronize the host and...
Trying to flash a program with Keil. Worked fine with SDK 5.2, now with SDK 6.0 get the error: Insufficient RAM for Flash Algorithms.
My options for RAM:
Start: 0x20002000...
Hi, Nordic
I added "//" to the srccode of main.c in project ble_app_hrs just like below
bond_manager_init();
// ble_stack_init();
ble_error_log_init();
timers_init...
L.S.
Suppose I want to customize the transmit power at installation time, not at build time or production time, how would I go about it?
I have adapted the proximity...
Hello,
I want to use DFU with single mode mode.
I included in build dfu_single_bank.c instead of dfu_dual_bank.c.
But after that DFU device begin to work with errors...
hello,
I am working with S130 demo app. But I could not find any registering of event handler being done usind softdevice_ble_evt_handler_set(). In both S110 and S120 demo...
With the maximum SPI speed of 8 Mbps, I was expecting to be able to send 2 bytes in just a little over 2 us, but it takes a lot longer. It appears that the mandatory event...
Hi all,
I'm trying to follow this Nordic blog post in order to use Luna Eclipse, GDB and J-link for debugging of ble_app_hrs from Nordic SDK 6.1 on a PCA10001
It is...
Hi everyone,
I dont know if I encounter these issues because of iOS 8.0 but I'm not able to receive data from the console, send via PCA100001, on my iPhone. Though, what...
I have managed to successfully integrate BLE DFU service in my app, but updating firmware via MCP is a bit confusing.
I connect MCP to my device -> discover services -...
Hi,
I plan to have my device without any forms of external user input, like buttons serial ports, and similar.
You can only replace the battery, that's it.
I'd also...
Hi,
I tried to migrate S110 example code with uart_ble service , which is working fine on S110, to S120 v2 soft device. Fix some minor missmatch with configuration structures...
I got the errror handler in the src\gap_core.c line 1473.
It happen when i do those steps with NEXUS 7 II.
Step1:
Use the Bluetooth to connect to the nRF51422
Step2:
...
I'm trying to change channel id with no luck while I'm in EVENT_TX state. It seems that if I call sd_ant_channel_id_set while in EVENT_TX broadcast data gets reset to zeros...
