Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
We have a custom board designed based on N51822, CEAAB0 and we have used the chip antenna from ST BAL-NRF01D3. When we have flashed our proximity code to the device, we will...
Hi,
After i use sd_ble_gatts_hvx() ,i will receive a BLE_EVT_TX_COMPLETE.
The "tx_complete.count" is no problem when i use softdevice 5.2.1 . e.g. count =1. this is correct...
Dear Sir,
i am using pca10001.
Actually i tried to read and write the data from EEPROM having address 0x50 though i2cbus.
i made po.0 and p0.1 as output pin then...
Hi,
I've created a small test program (pasted below) that is intended to help me profile some of my code down to us resolution. Maybe you can quickly run it (no other files...
I'm designing a board using the nRF51822 and leaving test points on the PCB for the programming/debug lines so the chip can be programmed after PCB fab. Are there any reference...
I'm evaluating nF51822 for my application which needs to wake up from either a button press or an interrupt pin singal from an accelerometer. Normally this can be done with...
hi guys, i am writing a code for reading data from a sensor using twi interface, the twi is not working properly, here in SDK i found two examples of twi - sw_ nd hw_ is sw_...
Hi all,
I have read the nRF51822_PS v2.0 and know that nRF51822 supports the SPI slave mode,so I want to know whcih version of the chip will support it?
Also,I have...
Hi,
is possible to reprogram flash in nRF51822 via radio channel?
If yes - is there application note for this feature
Some customer want to secure upload firmware without...
Hello, I need to transmit a data packet with hundreds of bytes, but aparently the S110 SoftDevice can't handle payloads with size bigger than 23 bytes.
According to the...
I load battery_demo_nrf8200.hex into nRF8200. I can then read battery data on Master Control Panel and watch data change when I change VTG.
I then load health_thermometer_application_nrf8200...
We need to customize the Gazelle protocol on nRF51822. To that end we will need access to the protocol source code - not just the API. Is it possible to progress this way...
Hello,I have a ble HID device,
it can connect iphone4S/Ipad with IOS 7 system,
but the function button of (page up /page down) can't work in app wps ppt.
but it can work...
