Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi The nrf9160 product spec 1.2 states that the number of times a 32 bit word can be written is 2. I have used the nrf52840 a lot and has a similar restriction but on seeking...
Hi,
In my project, there is a lockup issue like the title. (SDK 15.3.0_59ac345)
When I try to erase flash, some data (uart command for the device)comes up through the...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
Hello support,
Currently i'm working with one application using NRF52832.
in which i have to fetch data from coming from PIC controller to NRF52832 over UART communication...
Hello, I owe a nRF9160 DK version 0.8.2. The ERRATA 0.7 document says that for this version the GPS antenna does not work well. I need to use GPS for extracting PPS signal...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
Hello.
I'm beginner on Nordic product and checking the examples with nRF5_SDK_17.0.0_9d13099 on nRF52833 DK Board.
I tested ble_app_uart and it works. Now checking ble_app_hrs...
