Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am attempting to connect and send data between an nRF51422 (DK) running the UART Peripheral Example Code and an nRF52832 (DK) running the UART Central example. I am able...
We are a medical company utilizing the NRF51822 board with SDK 11 for our application. As part of filing for approval for our product from the FDA we are required to prove...
There is a corner case in pstorage_raw.c that can cause a deadlock between pstorage module and the pstorage system event handler. This in turn will cause all the future pstorage...
Hi,
I just implemented LESC Numeric Match on the NUS service for my peripheral device (based on ble_app_multirole_lesc example). I am able to connect to my device using...
I am using the esb_tx example on an nRF51 DK board modified to send BLE advertising packets at 1 KHz.
I am receiving the packets on a BlueTooth sniffer. The contents of...
Hi,
i'm designing a board based on NRF51822-QFAC chip and i'm using this antenna chip 2450AT43A100E and this balun 2450BM14E0003T .
I put the balun as close as possible...
I have __asm("BKPT #0\n") in my code. When running without a debugger, it seems to generate a hard fault exception (which I can tell because I have a hard fault handler that...
This week I worked myself to a series of what seemed to be problems boiling down to one issue:
The Notification Write Response is lost when bonding has to happen first. ...
I'm trying to save power on my HID keyboard application by disconnecting the Bluetooth link after some time of inactivity. As soon as there are keystrokes to send, the device...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
