Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I use a android phone as central(Master) and use a nrf51822 as a peripheral(Slave).
The peripheral can send the "L2CAP Connection Parameter Update Request" to change the...
Hi
I have a BLE nRF51822xxAA project created with Keil 5.15, SD 100 ver 802 and Family Pack 803.
I made a new configuration in a new machine with Keil 5.2 and I am getting...
I want to create my own PCB which can communicate with the following Transmitter:
www.hobbyking.com/.../_ 43854__Turnigy_5X_5Ch_Mini_Transmitter_and_Receiver_Mode_2 .html...
Hi! I work with a smart Beacon Kit nrf51822 rev1.0.0, s110 and I have visualised my current consumption. What I expected to see is that my beacon could send in one time all...
We are preparing a project where several mobile phones
with Android OS in peripheral role will be connected continuously to
one nrf51822 with S130. Communication must be...
On nrf51 I was using:
pre flash: w4 4001e504 1
erase all: w4 4001e504 2\n w4 4001e50c 1\n sleep 100
pin reset: w4 40000544 1
Is it still the same for nrf52...
[Edited title]
My application on a PCA10028 board is attempting to send a BLE advertisement using sd_ble_gap_adv_data_set() by going through ble_advdata_set in ble_advdata...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
is there something like a makefile for nrf52 out there?
I want to use eclipse and gcc in osx. It worked great for nrf512 but nrf52 has other addresses and maybe...
Hello all,
Lets assume that central bonded with nRF51822 peripheral and than disconnected. If bond is saved on peripheral- ok, cental send BLE_GAP_EVT_SEC_INFO_REQUEST...
When i try to do an update with Nrfutils Under android i get a REMOTE_DFU_OPERATION_FAILED since i added signing.
I created my pem file key with nrfutil.exe keys
i copied...
Hi
I'm trying to get working a project by using S132 v3 alpha. I'm stuck at function sd_ble_enable. This function should return the minimum RAM memoy would need the SD...
Hi Nordic.
So, I am using GAZELL to link a sensor node (PCA10001) to a host (PCA1000)
When the node is connected is should automatically send its address to the host....
Edit 2: Files need to reproduce the issue described in this questions:
pwm_conn_itvl_bug_files.zip
To reproduce the issue please just replace the main.c and nrf_drv_config...
Hi,I want to ble stay in fast connection interval after connection succeed. So I set the connection parameters like that:
#define DEFAULT_DESIRED_MIN_CONN_INTERVAL MSEC_TO_UNITS...
