Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I have set up the UART example with PCA10000 and PCA10001. Everything works fine but one strange thing is the time to send 100kB of data. See my times below:
38...
Hi !
On this thread devzone.nordicsemi.com/.../nrf51922-1 i've found someone introducing the new S130 softdevice for the nRF51822 wich allows the IC to be on concurrent...
Hi to all,
Ihave a problem with erasing flash on nRF51422 Evaluation Kit. When i click on Erase all button in nRFGo Studio everything is looking normal ( segger led is blinking...
I cannot download S110 to try right now. I have some 51822 Dev kits, but somehow I didn't get the product keys entered into my page, and the boxes are all gone.:D
When my application is running on the nRF51822 (e.g. the hrs example from the sdk), I want to stop this application (e.g. at a breakpoint), investigate some memory and than...
Hi,
I've started developing some test applications for the nRF8001 to better understand all the ACI libraries and improve my knowledge of the chip.
I'm experiencing some...
Unless manually set the value of bond_init_data.bonds_delete to true in the function bond_manager_init to clear bonded masters, I end up in the HardFault_handler. The last...
I'm trying to just set up a Timer for 8 MHz frequency and have that output on a pin. It seems simple but I'm having some problems (the frequency is a lot lower). What am I...
Hi everyone,
I've just started to develop software for NRF51822 - Bluetooth Low Energy on the Evaluation Kit. I managed to connect the development dongle and evaluation...
Based s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK v. 4.4.1
When scanning iOS, why not click pair on the iOS side and NRF51822
connected on? whether the pair can be...
Hi,
I'm planning a hardware solution and I need a BLE IC capable of act as a master and a slave, not at the same time, but with the possibility to change it's role by software...
I used nrf8001 to implement ANCS.It working fine.But when it disconnect for a while and reconnect(reconnect successed).I found Iphone can't send any ANCS message to nrf8001...
Hi, I would like simplify the nRF24AP2-8CH signal RF output using a Balun with a chip antenna.
What is the best way: the 2450BM14A0002 from Johanson, the BAL-NRF01D3 from...
