Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
This is a followup on https://devzone.nordicsemi.com/f/nordic-q-a/119259/synchronisation-between-tx-and-rx-in-connectionless-direction-finding
We now have a synchronised...
I am using OpenThread network and working on CoAP Client and Server examples (Customized). Everything working fine when devices are on main power.
My client devices are...
I am running VSCode with the latest nRF extension. I am on v2.9.1 of the SDK
I created a new app and copied the bluetooth_st_ble_sensor sample project.
I would like to...
Hi,
I used the nRF52840 board with SDK v2.8.0 .
When we tried to build this example code, we encountered the following error: v2.8.0/zephyr/include/zephyr/device.h:92...
Hi!
S132, SDK17.1, nRF52832
Very strange behavior, I connected my central to the bonded peripherial success and got an BLE_GAP_EVT_CONNECTED event, but when I disconnected...
Hello,
I'm working on a custom board with a nrf54l15 chip.
I would like to add an interruption on the GPIO P2.10. But I get an error -ENOTSUP with gpio_pin_interrupt_configure_dt...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
I am developing a device that uses ESB.
Uses modules that are Telec and FCC certified with BLE profiles. (module : MDBT50Q-512K)
I have a few questions.
Q1. The TX power...
I have two boards:
nRF52840 DK (which has a faulty buck converter, so I am powering it via USB).
Fanstel BT840F board , which provides power to the Debug In connector...
I used nrf5340 on my board and did some changes based on audio demo.
Unfortunate,I heard a noise after set configure like bis gateway, audio input from usb ,48k 16bit 2channel...
Hi,
I have a problem with unmodified BLE Shell and changing security level to 2(aka just works).
1. I'm connecting from BLE Shell to the device that requires level 2 2...
I am attaching an adapter board to the nRF52840DK to debug a custom board.
However, if there is any contact failure on the adapter board, the nRF52 on the DK will be the...
