the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I am planning to design a custom board using nrf52840 Soc which receive analog signal from sensor and send ADC outputs through UART to smartphones using Bluetooth communication...
Hi, Everyone
I use sdk15.2 & nrf52832
I am doing a test to read the slave address in TWI
There is one slave device on the board and the slave address is 0x68
I used three...
I am working with SPIS example ( sdk version 15.3). SPI master send data regulaly. For example, it sent 5ms cs low, but there are only two bytes transferred, the first byte...
Hi,
I'm working on a project that is using the the freeRTOS and I want to use the NFC pins P0.9 P0.10 to drive SOFTWARE SERIAL UART with a timer like TIMER1, when I try...
iPhone 8 Plus with nRF connect App[iOS], does not shows BLE 5 beacon in scanning, it only scanning BLE 4 beacons, In Spec of phone it shows it support BLE 5
nRF connect...
Hello,
I follow the nRF Connect SDK on a Windows 10 x64 computer and it's a crap. I get a lot of errors like this one. It's so crappy that I doubt that I will continue with...
Hello,
I am not able to send a command from the BLE (52810) to a DSP over UART which are on my custom board. I have modified a program that uses UART for logging purpose...
The s132_nrf52_7.0.1 documentation says: Call stack: The SoftDevice uses a call stack combined with the application. The worst-case stack usage for the SoftDevic e is 1.5...
I am doing a program based on Current Time Application example. But I have a few questions, so I hope you can help me. First, I am using Battery service together. By the way...
Hi,
In our current project we use nordic NRF52832 ble to send some data(~200 Byte / packet) to host, we expect each transmission to be done within 10ms, but results from...
Hello. nRF52 A custom board is being developed. I want to use Crypto Chip Pulse to encrypt. Pulse_Out of Crypto Chip is connected to P028/AIN4. In order to measure Pulse,...
I'm using \nRF5_SDK_15.3.0_xxxxx\examples\peripheral\usbd_ble_uart example to use two communication links. Missing echo on the USB virtual COM is a small frustration. I've...
Hi NordicSemi
I have a project where we receive data via the UARTE. To avoid missing data caused by higher prioritized tasks we want to use the DMA facilities.
nrf52832...
Hi,
i want to flash programs with the Segger Embedded Studio to my Thingy 91. I already am able to flash hex files with the nRF Programmer to the thingy 91. I installed...
