nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I'm converting an SDK 14.2.0 project to SDK 15.0.0 using the legacy functions and ARM GCC. It compiles OK but linking is failing.
The verbose output appears to be the Make...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
Hi,All,
I am using nrf52832 as a slave, the SDK version is 12.3. I set the connection timeout to 10s as follows
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(1000, UNIT_10_MS...
Hi,
I'm having an issue to connect a Galaxy samsung Tab A to my ble device.
Each time i ask for a connection i get the same error.
I already succeed with others phone...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
