Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I would like my device to advertise for 10s and then begin advertising again only on an external interrupt.
What steps are required to restart advertising without restarting...
I am trying to reprogram a usb dongle device from AdaFruit (Bluefruit LE Sniffer), which uses the nrF51822 SoC, using nrFGo Studio. In the device manager I'm innRF5x Bootloader...
Hello everyone
i am trying to set the password for connection whenever its start advertsing but the static passkey option will set the pssword only for bonding not for...
Hi.
I am using nRF24, nRF51, and nRF52 chips.
Today I saw nRF31562A on some device(wireless mouse of Logitech)
However I can't find any information about this chip,
even...
Hello,
I would appreciate if you could help me solve what i am trying to do. I have nrf51DK board with nrf51422 on it, PCA10028, S130 and i want to use to scan for another...
Hello,
I am working on SDK 9.0 and softdevice 8.0 and the requirement for my application is the device has to advertise till it gets connected and even after disconnection...
Dear all,
I get a new nRF51-DK and I am trying to download an hex file into it.
I downloaded and installed nRFgo studio.
I connected my nRF51-DK to my...
Hi. I've gone through a lot of documentation and can't seem to find if this is documented by Nordic semi.. please answer if you know, or can point me to experiments/documentations...
I soldered 5 pieces of PCBA with nRF51822, but I got only one PCBA which can connect to J-LINK. I checked the bad four and found that SWDIO of nRF51822 on the four board is...
I'm having a weird hardfault and, I can't make sense of it.
Here's what I do know:
nrf sdk 9.0.0;
nrf51422 on a dk;
I have RTC1, SPI0, and TWI1 enabled (also a uart for...
Hello,
call of app_pwm_init() function forces logic 1 on PWM enabled pin after advertising timeout expires. Why? It causes my LED to turn completely on after advertising...
Hello,
In my code I would like to switch between BLE advertising and listening nearby devices (and save their RSSI) in the same code. After each advertising period, I would...
i have use nrf51822 and android app(nRFuart)
i was masure currunt through DSO but i think its not accurate...
i can't masure exect(high accurate) currunt consumption in...
I read through the following post and still couldn't get debug info out.
I have tried the settings there and from another post with no luck. I'm using putty on a win 8...
Hello everyone,
I am trying to enable notification on a characteristic based on the code example from nAN36.
Unfortunately the sd_ble_gatts_hvx() function returns:
...
