Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello.
I'm working on disconnecting ble from the module.
I'm using the app provided by nordic.
I designed it to disconnect the ble when I press the button on the module...
hi.,
we develop a product that use nrf52840,and it need to suport usb dfu in windowns and mac.and also need achieve cdc communication .this funcation is ok in windows,and...
USED SDK: v1.4.99-dev1
USED BOARD: nRF9160DK
Received hexvalues above 0x7F (decimal = 127) are counted double in p->message.payload.len Any ideas what might be te problem...
We are trying to evaluate the BLE Mesh for a product range and are evaluating the nRF52832 for the same.
Working with the nRF Mesh SDK, I am facing some issues, which are...
Under the recommended operating conditions (page 611) in the nRF52840 datasheet, there is a note specifying:
Given a device (with SWD access), is there any way to detect...
Hello Sr,
Take a look below Error, when I run the demo code from
C:\..\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\multiprotocol\ble_thread\ble_thread_dyn_mtd_coap_cli...
Hi,
We have created an application with BLE multi peripheral where I have to put my chip into deep sleep mode by long pressing the tactile button & also I have to wake it...
In the nRF51822, there was a bootloder area, but in the nRF52810, there is no area except for Application, and the image is as shown in the map below, is that correct? --...
Situation: SES, SDK 16, nRF52832, no BLE.
I'm trying to use both the UART and TWI 0. TWI works fine with BLE and all the rest. However, when I enable the UART, TWI quits...
Our device has been in use for a year using the nRF52840. We elected to not load the 32KHz crystal on our board. Everything seems to work OK and we have no BTLE issues, however...
Hi,
I'm using nRF PWM Driver and I didn't find the way, how to invert logic of PWM. I would like to reach this behaviour:
If I set seq_value=0, I want to have
PWM...
