I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi all the Nordic friends and Team,
I would like to do a Batch OTA of one hundred devices right now... I'm on the NRF52 stack for my devices to be flashed. And I'm using...
I test SoftDevice V6.0.0 on nrf52832(BLENANO2) I run 1. sd_ble_gap_scan_start() 1000ms/100ms/10ms scan_window/scan_interval 2. sd_ble_gap_adv_start() 1000ms interval result...
When my mobile phone reads my characteristic, I would like the characteristic to be calculated at the same time, and not before. i.e. like a video game that does not render...
Hello Supporter,
I am Using NRF51822 QFAC .
My probleme after uploading DFU ,SOFTDEVICE AND APPLICATION .device always in DFU mode and also when try to upload new application...
Hello Supporter,
I have NRF51822 QFAC having 256kb ROM,32kb RAM.
now i want to upload all three things DFU,SOFTDEVICE,and APPLICATION .when i upload SOFTDEVICE and APPLUICATION...
Getting ready to go into production with our custom nRF52832 board, we need the board to start running our application immediately after being flashed. Using:
nrfjprog version...
Hi all,
I want to add 5 characteristic to my custom service . But when I add 2 characteristic , it worked fine . When I add 3 characteristic ,In funtion sd_ble_gatts_characteristic_add...
Hi,
I am trying to read data from a temperature sensor, but i'm stuck at the twi read operation. i have already interfaced the sensor with esp32 and is working fine. please...
Hi,
I have a really really dumb question but I will ask ...
Is there any impact regarding the orientation of an IFA antenna?
Everywhere, in all examples, we can see...
Hello everyone,
I'm trying to implement the bootloader from SDK v14.2 on the nRF52840, SD v5.0.0 s132 (using our board and app).
For my testing, I erase the whole flash...
Hi Forum,
i've started the development of an custom service on a nrf51822 with s110.
The Service contains 4 Characteristics where notifications are enabled.
At the...
I have a custom dongle that connects to the PC through a USB-UART chip. It is based on the nRF51822. I have another board based on the nRF52832. This board needs to be able...
Hi,
I am building a device to act as an iBeacon, with other services layered on top. This is based on a Raspberry Pi with a Class 1 USB Bluetooth dongle.
I need to be...
Hi everyone, I'm working on the nrf51822 QFAAH I tried to flash the ble_app_uart example and it didn't work. So I debug it and it stops here
As you can see in the picture...
I am working on app_uart and buttonless_dfu. Although i am getting certain errors which i am unable to counter.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
