Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
On November 19th, I participated in the 2019 Nordic Tech Tour with my colleagues, but some of the content was not clearly understood, especially regarding the development...
Hi all. I want to measure current consumption on nRF52840 DK (PCA10056).
I have the SB40 cut and the 12 Ohm resistor placed in R90. I measure the voltage on this resistor...
Dear team：
How can I use ble-bas-c to change Characteristic UUID or Connect the 1800 service and rename it with the 2A00 feature value The example is \SDK\nRF5_SDK_15.3...
Hi,
I am new to this. I want to build a mesh network using nrf52832. I have already downloaded and gone through nrf5 SDK for mesh but i am confused about what to use to...
I am using nrf51822 DK. How to set GPIO pins as output pins and access the pins to set or reset the output.For example if I want to use pin 20 as output, how to configure...
I am trying to read if an input is 0 or 1 but for some reason it takes the first one its offered and then it does not change anymore.
int main(void)
{
nrf_gpio_cfg_output...
<Environment> - nRF9160 DK v0.8.5 - nrf tag: 1.1.0 - modem version: 1.1.0 - using an external GPS antenna, SW12 => CON
I'm attempting to use udp_gps, but doesn't work out...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
Hello. I am using nRF52832. The SDK version is 14.0.0. UARTE is used for serial communication with other devices. The baud rate is 38400bps, and a maximum of 20 bytes of data...
Hi, I could not find a way to use Segger Studio debugging features when I have a bootloader for DFU functionality. Is there a way to something like that, because when I click...
I am trying to read temperature, pressure, and humidity data from an Adafruit BME280 sensor using the nRF9160 DK. The communication protocol that I am using is I2C and I am...
