I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi Team,
Iam doing project called automation of light using BLE technology.
Here Iam using sdk 12.1.0(ble_app_hrs_c) example for scanning or receiving and i flashed...
I have a small problem with my bootloader + application on NRF52832. I'm using SDK 12.2.0 with S132 v3.0.0.
When the device loses power, and power is then re-applied, the...
I'm using nRF52 + s132v2.0.0 + SDK11.0.0. I want to be able to update to s132v4.0.2 (or so) + SDK13.0.0 via DFU. I'm planning on modifying the bootloader start address to...
I'm using nRF52 + SDK11.0.0 + s132 and have a couple of questions on DFU.
I want to use a CMSIS-DAP programmer + OpenOCD to upload the bootloader (or BL+SD+APP+setting...
Hi,
I am using a nRF51822 board and I wanted to know if the LC filter is necessary if I don't need to use any analog entrance or exit. I just need the BLE and a digital...
Hello,
I was trying to load code in pca10028 and I started getting error as "No cortex M Sw device found".
It was working properly but later it started showing me this error...
Dear Nordicers,
I have an application where node based on s132 sofddevice 4.0.2 has multiple connections as a peripheral and as a central. The case is about non overlapping...
I have an NRF52832 DK [PCA10040, V1.1.0]. It used to do programming with it, but now it suddenly stop detecting as "JLink" in Windows, Linux and Mac. Now when I connect it...
Hi, I use the twi_master_using_app_twi_pca10040 (SDK 12.1) to test the TLC59116 LED module .
By changing the example project's code by referring the GitHub code, I have...
Hello the Nordic Team,
I come here after a lot of research and testing and do not understand what is going on in my program. (is it Embedded or iPhone nRF Toolbox side...
hi,
I follow the pwm routine, 51822 can work and output pwm, when I want to change the frequency of pwm encountered a problem, the program reset.
I use the method when i...
Hi,
I'm using Nrf51822 to implement a RTC(200ms tick)
I connect a external 16MHz crystal to the MCU.
I use the S110 softdevice with BLE function enabled, so it's in ble_stack_init...
Hey. Has anybody played with autocomplete for command line interface.
I like it alot and it is very helpfull. Now a autocomplete would be cool!
Here is what comes to mind...
How to setup a nRFDK52 as a central and nRF bluetooth kit as peripheral. Should I use nRF go studio? Do i need to load the soft device first before loading the app? What is...
I want to store two floats and one 8 character string in fstorage.
I solved it by using 4 uint32 types stored in flash, I got it working in the ble_app_template example...
