I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello.
I use s130 2.0.0-7.alpha stack and thus app starts at 0x1B000
Questions:
How to change default app start address, for example to 0x25000 ?
How...
I'm using the nrf51822 EK board (pca10001). I'm able to connect fine from my laptop (using Bluez) if I use a random address on my laptop. However, if I use a public address...
I am new to Nordic Evaluation Kit.
I am working in Nordic nrf51822 (PCA10001) Evaluation board.
Following are my setup.
OS : Ubuntu 14.04 64 bit.
SDK : nRF5_SDK_11...
Hi all,
I need to know the RSSI Value (distance) between my nRF 51 DK and my connected device (iOS Device). I made these code changes:
switch (p_ble_evt->header.evt_id...
Hello!
I've been using RTT viewer to view some data in my nRF52832. Everything works fine but I am unable to clear the RTT viewer terminal screen.
As it is in the manual...
Hi,
I am trying to get the experimental NFC example "HR with pairing over NFC" to work.
I can read the tag correctly with an android phone : the NDEF message is correct...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
