Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
Our team has identified an opportunity that your nRF52832 fits well, I am having a difficult time getting started with your Bluetooth SDK and reaching out for assistance...
Hi,
As simple as the title! I have tried to move my code from sdk v 3.1 to v3.2 but it will not join the network.
Back to basics and using off-the-box ligh switch example...
Hi
I have been working with the nrf52832 breakoutboard from sparks fun and the nrf52 10040 Dev board.
I want to work with SPI communication in order to intergrate an accelerometer...
I'm having an issue with some iPhone11's, where under certain conditions the iPhone11 is sending two consecutive Link Layer requests with a Control Opcode of 0xFF. The SoftDevice...
Using zboss_start_no_autostart() instead of zboss_start() will cause a power consumption of 630uA. I was expecting the device to be sleep and in a very low power mode.. All...
Hi
When I use the nRF5_SDK_15.3.0, the nRF52832 cannot enter low power (about 900uA). The example is file ble_app_blinky.
The main code is as following:
int main(void...
Hello,
I want to blink the LED by pressing button on nRF9160dk. Is there any sample available to start with?
I started with button demo but on button press there is no...
Hello,
I am using SDK 15.2, could someone please tell me the location of pstorage.h file in the folder. (I found pstorage._platform.h but I cannot locate pstorage.h.)
...
Hi nordic,
I am developing with nrf52832, s132,v15.2,0.I am using secure dfu bootloader. But its connecting in nrf_connect app, after connected, i got this below mention...
Hi,
I'm wondering if you will support sending data using control plane (CIoT EPS Optimization using CP) and Non IP Data delivery for CATM . I assume you will do it for...
Hi:
I am running the example program ble_app_att_mtu_throughput on the SDK52 for the NRF58232 and the NRF58340 next.
My question has to do with how to modify the example...
I'm trying to simplify the open_bootloader example from SDK 15.3. I'm getting rid of version, signature and keep only the CRC validation. I'm actually trying to understand...
Device: NRF52832_xxAA Softdevice: S113 v7.0.0
Hello.
Sometimes, during firmware running, I get a fault from Softdevice with pc: 0x0001A990. Could you inform me what causes...
