Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Do you why I could not pass the "ble_stack_init()? I did download softdevice from 0x0000-0x26000 and Application from 0x2600
int main(void) { // Initialize. log_init();...
I can run some of the samples on my nrf9160 DK, however when it comes to this one I get a assertion error err==11 that I have not yet been able to solve.
ncs/zephyr/subsys...
Hi,
In my application I need accurate calendar capabilities such as alerts on every hour and alert on a specific hour every day. Is there any implementation of such a mode...
Hi,
Want to read data from HX711 adc amplifer with wheatstone bridge loadcells, but when i run the program, my output is <info> app: ADC measuremement -8388608 all the time...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
I am trying eddystone example from SDK 15, its working fine but once I press the button to enable connecting and function nrf_ble_es_on_start_connectable_advertising(); is...
I want to use REG0 to supply 1.8v to external 4.7k pull-ups including when the system is off. Looking at the product specification REG0 can supply 1mA while in system off...
I have updated my repos to the latest commits on master for zephyr, mcuboot, nrf, and nrfxlib. I ran `
pip3 install -r scripts\requirements.txt
and I can open the asset_tracker...
hi, I'm working with NRF52832, DFU service is configured as secured. my question is : i'm trying to change dfu char a ct e ristic property to "ind i cation" by writing to...
Hello
I would like to test if provisioning over GATT Bearer still works with our application. Firstly I thought of using the serial example together with the PyACI, but...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
