I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
I am working from the ble_app_hids_keyboard example. To support multiple centrals, I imagine the first step is changing NRF_SDH_BLE_PERIPHERAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am trying to set up eclipse + gdb + openOCD for debugging zephyr 2.0.0. applications on nRF52832. Following the official Zephyr documentation build-and-run-an-application...
Hello,
I am using NRF52832 with soft device 13.0.0 and Nordic's bootloader from the examples.
What I do is develop an application which stores some values in uicr registers...
I'm using 52810 with s112 stack.
And I need two PWM channel with different frequence. one channel set to 4KHz to cotroller BEEP, the other one set to 15Khz to control...
Hi, I've completed the first 3 BLE tutorials (about advertising and Services).
I've got notifications up and running on the peripheral by using a timer and hvx as in the...
Hi,
We are developing a mouse . The controller we are using is NRF52832 QFABB0.
You known that its contain 32KB RAM and 256KB of flash memory.
Our application contains...
Dear,
Currently, I can run asset_tracker application with THINGY:91 PCA20035 and I am looking for more examples for this one.
On Thingy:91 FAQ :
@ Peder Rand mentioned...
Hi,
Experimenting on a stepper motor control (DRV8834). I want to be able to send a single square wave output, with a specified number of pulses. I managed to put together...
Hi!
I use SDK15.0 on a central side with nrf52832 with bonding and work with whitelist.
On the peripherial side I use nrf52810.
All works fine, all bonded and work with...
I was successful in flashing the dongle using SWD and the development kit. I used the blinky example. It all works perfectly. However, as soon as I reboot the dongle, it goes...
