I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi. We have a project we would like to move to an nRF52840 SoC. I have modified the hid generic example to connect with our test software which basically can send and receive...
Hi all!
I want to make my first code in my nrf51 dk (i have an PCA10028). I have experience with M0 and other uC, but i have never play with BT.
Could you guys recommend...
Hi,
I'm trying to improve throughput by increasing the notification buffer number to 6. (SD132, V 5.0.0, SDK14.2)
I tried to follow the sequence charts as well as use...
I'm in trouble because I can't get my expected Logs in WireShark with nRF51822.
[Enviroment] ・I use "User Guide v2.2" and I installed according to this document. ・My PC...
Hello,
I'm using the nRF52832 DK to implement the light switch example in mesh SDK. For this example I'm using nrf mesh app as the provisioner and in this app , to add a...
nRF52832 power consumption is high after the SPI peripheral is used (approximately 400uA of extra current consumption). I expect it has something to do with the high speed...
Hi,
I am using the nrf52832 board for my project.
I am using the NUS example as a base for my project.
2 services are provided by this application i.e RX Characteristic...
I'm trying to flash a Nordic Thingy. I have it connected to the debug port of a nRF52840-DK, nrfjprog --ids lists no boards, however.
However pyocd produces:
...
I have a question about bonding with "Peer Manager".
I am using the sample project "ble_app_multirole_lesc (SDK V15.3.0)".
I am bonding by "Peer Manager". When bonding...
Why does SPI not work with nrf_delay, from this previous question
devzone.nordicsemi.com/.../
Surely the SPI SCK is a PWM or other timer/interrupt driven clock?
Also...
When i use nrfutil to perform DFU it is passed, but when i send it through STM32 dev kit it Hash validation failed. but however i can see the CRC is correct.
Hello,
I have an AMS AS7261 light sensor that I'm using with my NRF51422 DK to take a light reading, pull it using nrf_drv_twi_tx/rx, and send it over BLE. However, when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few variables in application. These will...
i have a complete project based the gfx project and i want to add BLE using UART for communication. i want to communicate my module with the nRF52840 dongle.
is there simple...
