After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
On powering up the nRF52840 I start the twis slave. The nRF52840 works as expected.
I install one i2c slave address on the system, external master has no issues communicating...
Hello,
I am using NRF52832, SDK v15.1.0.
For entering into various power down modes, does calling corresponding functions is enough to make entry into these modes or...
Hello !
In my project I have 3 phones, witch connects to one nRF8001(not at the same time).
First, phone connected, bonded and bond of this phone saves in EEPROM of avr...
I am upgrading our Nordic / BTLE library to the new sdk, which gains us ble 5.
The previous library (based on sdk 11.?.?) made light use of pstorage which, as far as I can...
I want to set up nrf24le1 in register retention mode with analog comparator wake up. The moment it wakes up it should do few ADC conversions and then again go back to sleep...
I have built up most of the support structure using the existing ble_app_uart example from SDKv15.0.0 and am now ready to port the code to our existing devices.
I'm having...
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132 from SDK 15.0.0
My hardware is a custom board with a Rigaldo BMD300...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hello,
I have developed my own iOS app which is capable of DFU update different devices with nRF51 and nRF52 chips.
Using only APP file (both .hex and .zip) works perfectly...
Hello,
I' trying to switch from keil uVision to Eclipse, but it doesn't work as intended. I can't debug them (hrs with and with out dfu), but the Blinky example works...
Hi,
I'm working on a custom application using two microcontrollers a pic32 and a nrf52832, I require the pic32 using an external flash memory to read the binary file stored...
I'm interesting in knowing a little more about the "address match" output of the nRF905 chip. What is the expected jitter related to the actual radio signal?
E.g. If I...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
