Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
Hi Nordic team
I have a question about Litepoint bluetooth advanced nRF5x OTA Testing.
According to the White Paper v1.0, by using the heart rate app, it is easy to evaluate...
Hi,
I am using the ble_app_uart_c example for the ble_central of SDK 12.2.0 to send data over UART to a nrf52832 based peripheral. When following the format as suggested...
i use sdk14.2 52832 as central , have bas service and myself service it have pair process , there are one change question. When I first burned the program, the bas service...
Hi,
I'm using Noble.js on a central RPi3 for DFU updates over BLE. The process is several times slower than doing the DFU over nRF Connect on an Android phone. I believe...
I am designing a NRF52 based device. One of the component , Crystal X1, EPSON FA-128 32.0000MF10Z-AJ3 used in the reference design is not available for purchase in online...
On the included Thing52 example, the LED fires m_ioext_osc_status_change from an interrupt. Eventually, when it comes to requesting use of the TWI this comparison happens...
I've noticed that if I call app_usbd_cdc_acm_write with the length set to any multiple of 64 the data will not show up on my PC until I do another write with a value that...
Hi DevZone,
I am modifying an CAN library for nRF52840 preview DK. In my project, nRF52 preview DK is working as a SPI master and Arduino CAN Bus Shield is working as a...
Hi,
I am developing a device using the PCA10028 Dev Kit
It is configured as a BLE Central, SDK 7.2, SD 120
I am starting out with the example "ble_app_hrs_c_s120_pca10028...
Hello
Ive implemented and modified the light_switch_example and now I want to change the tx_power(sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle, int8_t tx_power...
I am writing a program that waits for button 1 to be pressed. once it is pressed for 5 second it will call the LED ON api and when button 1 is pressed again for single shot...
